PIC16Fxxx的LCD驱动程序(适用于HD44780兼容的驱动器)

;************************************************
;* LCD.ASM                                      *
;************************************************
;* Contains subroutines to control an external  *
;* lcd panel in 4-bit mode.  These routines     *
;* were designed specifically for the panel on  *
;* the MCU201 workshop demo board, but should   *
;* work with other LCDs with a HD44780 type     *
;* controller.                                  *
;* Routines include:                            *
;*   - InitLCD to initialize the LCD panel      *
;*   - putcLCD to write a character to LCD      *
;*   - SendCmd to write a command to LCD        *
;*   - clrLCD to clear the LCD display          *
;*   - L1homeLCD to return cursor to line 1 home*
;*   - L2homeLCD to return cursor to line 2 home*
;*   - PutHexLCD to write a HEX Code to LCD     *
;*   - Hex2ASCII to convert 4 bits to ASCII Code*
;************************************************
;
  list p=16f877
  ＃i nclude <p16f877.inc>
;
; Defines for I/O ports that provide LCD data & control
; PORTB.0 - PORTB.3 are Data Pins for LCD Module
; PORTB.4 is E Control Signal for LCD
; PORTB.5 is RS Control Signal for LCD
; PORTC.2 is BackLight Control pin for LCD Module
;
  global InitLCD
  global putcLCD
  global clrLCD
  global L1homeLCD
  global L2homeLCD
  global  SendCmd
  global PutHexLCD
  global Hex2ASCII
;
LCD_DATA equ PORTB
LCD_CNTL equ PORTB

; Defines for I/O pins that provide LCD control
RS  equ 5
E  equ 4

; LCD Module commands
DISP_ON  EQU 0x00C ; Display on
DISP_ON_C EQU 0x00E ; Display on, Cursor on
DISP_ON_B EQU 0x00F ; Display on, Cursor on, Blink cursor
DISP_OFF EQU 0x008 ; Display off
CLR_DISP EQU 0x001 ; Clear the Display
ENTRY_INC EQU 0x006 ;
ENTRY_INC_S EQU 0x007 ;
ENTRY_DEC EQU 0x004 ;
ENTRY_DEC_S EQU 0x005 ;
DD_RAM_ADDR EQU 0x080 ; Least Significant 7-bit are for address
DD_RAM_UL EQU 0x080 ; Upper Left coner of the Display
;

; Directs linker to provide 4 variables in GPR memory
  UDATA
Byte  RES 1
Byte1  RES 1
Count  RES 1
Count1  RES 1
W_BUFR  RES 1
Hex_Bfr   RES 1
;
PROG1  CODE 
;*******************************************************************
;* The LCD Module Subroutines                                      *
;* Command sequence for 2 lines of 5x16 characters                 *
;*******************************************************************
InitLCD
  BANKSEL TRISB
  movlw 0xc0  ; Initialize inputs/outputs for LCD
  movwf TRISB
  BANKSEL LCD_DATA
  clrf LCD_DATA ; Clear LCD data & control bits
;
  movlw .50  ; Power=On delay 50mS
------------ ---------- ----------- ---------- --------- -------- ------- ------ ----- ---- --- -- -  -  -

• 上一篇：使用PIC读写1-wire EEPROM DS2430的实例程序
• 下一篇：HOLTEK主I2C的源程序代码